Where can I buy EASYJoint - 'the all weather jointing compound'?
We have dealers of our EASY Range 'all weather jointing compound', to find your nearest EASY Range dealer call us with your postcode and we will direct you to your closest EASYJoint dealer. However if your local EASY Range supplier has run out of our paving compound we can normally get it to them within a couple of working days or we can direct you to another dealer who does hold stock. Alternatively there are on-line 'internet' companies that you could contact. Our phone number is 800-395-9701 - call us and our EASY Range support team will be pleased to assist you.
Can I use a power washer to clean the paving and joints?
Yes, you can clean our paving joints with a pressure washer but it must be done cautiously and after the EASYJoint sweep in sand has set hard. We recommend leaving newly laid EASYJoint for at least 4 weeks before cleaning it. When you clean the patio hold the power washer at an angle of about 45⁰ degrees and using a fan spray from no closer than 150mm from the paving joint. For stubborn stains and dirty paving, use our EASY Care Patio & Deck cleaner - for extremely contaminated areas of paving, natural stone or garden ornaments use EASY Care Masonry Cleaner. EASYJoint paving compound sets hard on contact with air but remains permeable. As water drains through the joints contaminants in the water will collect at the surface of the paving joint but these can easily cleaned & washed away, leaving the paving joint looking like new.
How deep do the paving joints need to be?
The recommended minimum depth of the paving joint is 25mm. It needs to be this deep to ensure the jointing compound has the correct strength to be a long lasting paving joint.
What is the minimum width a paving joint can be?
The paving joint needs to be a minimum of 3mm wide, (what is described as a narrow paving joint) however care should be taken measuring this as with some 'V' shaped paving the joints at the bottom edge can be narrower than the top. EASYJoint is designed to be a narrow joint filler and is probably the best on the market. Note there is no maximum paving joint width, feel free to use as much EASYJoint as you like!
Can EASYJoint be used with any base mix? (Base mix or the bedding mixture - parts or ratio of 'sand to cement' that the paving sits on).
We recommend a 6:1 bedding mix, six parts sharp sand to one cement. At this strength your bedding mix will remain permeable and allow water to drain through it. A stronger mix may cause the base to become impermeable and this will mean that water does not drain away. EASYJoint goes hard on contact with air, our EASYJoint needs to sufficiently dry out to allow it to cure properly. When using the wet method - the water is used to assist our jointing compound into the joints, it will self-compact and fill any voids. It also makes it easier to move around the paving and prevents staining. NOTE: You can still use EASYJoint on a stronger base mix but you will need to use the 'dry application method', remember EASYJoint does not need water to harden but is makes it easier to use. For the dry application or the method to joint a driveway - please refer to our instructions and follow the advice given on domestic driveways.
Does EASYJoint come in different colours?
Yes, our paving compound comes in five great colours. Mushroom, Buff Sand, Stone Grey, Basalt and Jet Black. Our range of EASYJoint paving joint colours enables you to individually design your patio. You can be as bold or refined as you like with your patio styling! EASYJoint - 'all weather' jointing compound is made in the UK. Rain or shine EASYJoint goes in fine!
How does EASYJoint go hard?
Simply on contact with air. To ensure EASYJoint reaches our customers in tip top condition at the end of the manufacturing process air is removed from the bag holding the EASYJoint and replaced with nitrogen. As EASYJoint needs oxygen to cure - once the bag is opened, and air gets to it, the curing process commences. EASYJoint can be stored in the tub once the bag is opened by keeping it covered with at least 2 inches of water and replacing the lid - it will keep for up to 12 months.
It was raining when I put in the EASYJoint and we are still getting showers, will it affect the drying time or appearance of the finished look?
EASYJoint will not harden until it has dried out - if it stays wet it will remain soft. Heavy rain may disturb the sand grains on the surface of the joint. If the joint has been 'striked' or 'tooled' this process may have to be repeated to achieve the desired finish. EASYJoint will go rock hard when it is exposed to air and allowed to dry - this may take 3 to 5 days (depending on weather). If the paving joints only partially dry out and then are repeatedly allowed to get wet, partially dry out etc, over a period of time, the curing process may fail altogether. See notes on permeable bases.
Why do you need to soak the paving before using EASYJoint?
There are three key reasons why using plenty of water with EASYJoint is essential. Water helps the user to sweep our paving compound around the patio, it also allows the compound to compact itself into the joints. There is no need to push EASYJoint into the joints, our paving compound does the hard work for you, falling into the paving gaps, filling voids and compacting. Lastly is contains linseed oil, a vital ingredient to create a strong bond in the paving joint however to avoid this oil penetrating the paving stone the EASYJoint instructions inform you to thoroughly soak the paving, this keeps the linseed oil 'floating' on the surface of the water, rather than penetrating the stone. It is important to note that linseed oil staining is only a temporary stain and exposure to sunlight, will over time, lift the marks.
Will EASYJoint mark my paving?
If used correctly in line with our instructions it should not, however there is always a chance that the Linseed oil will seep into the paving, linseed oil. Linseed oil is a vital ingredient which creates a strong bond in our paving joint. It is important to note that linseed oil staining is only a temporary stain and exposure to sunlight, will over time, lift the marks and fade away. Do not be tempted to use brick acid on natural stone, it will damage the paving and possibly the paving joint.
I have a block paved patio, can I use EASYJoint to point it?
No, the joints will be too narrow, we recommend a minimum of 3mm. The best solution would be to get it laid as recommended by the suppliers and to then protect it by sealing it with one of our specialised EASYsealers, either EASYSeal Paver Sealer & Binder or EASYSeal Paver Sealer. Both have sand binder in them and work in similar ways however EASYSeal Paver Sealer & Binder is the superior product and lasts longer.
Why do you need to use lots of water to wash in EASYJoint?
Simply to make patio laying EASY: We say 'the wetter the better' because it flows into the paving joints filling voids, compacting itself within the joint and giving you a stronger paving joint that will last. It is also easier to push around the paving and prevents the linseed oil within the EASYJoint marking the paving. We recommend using sufficient water with EASYJoint to turn it into a slurry, it works incredibly well with paving joints of different sizes (miniumum 3mm) - View the EASYJoint demonstration video and see how EASY it is to joint a patio using EASYJoint.
The paving I'm using is sensitive to marking, is EASYJoint a suitable product?
Yes however only if used correctly by following the 'how to point paving' instructions in the EASYJoint tub or on this Azpects website. We recommend that sensitive paving, such as Granite, Black Limestone and Modak is sealed to protect it from staining before using EASYJoint. It is recommended that the paving is sealed before it is laid so that the edges and even the underside can be sealed. Granite is particularly prone to drawing contaminants up from the sub-base, through the granite and staining the surface. Our sealers can protect natural stone paving from staining, we have tested different types of natural stone with our EASYSealers - Our sealers will protect natural stone and concrete. Resistant to tea and coffee spills, red wine and engine oil, mayonnaise, vinegar and ketchup etc. Look at the sealer comparision chart for help choosing the right sealer for the job in hand.
What do you mean by the joints are permeable?
EASYJoint allows water to pass through it - it's a permeable or porous jointing compound. EASYJoint resists weeds growth. Sometimes the joints trap dirt at the surface as the water drains through it. EASYJoint can be cleaned to remove these particles.
Can I use EASYJoint with a driveway project?
EASYJoint does not form a structural part of any paving or driveway project, it only serves as a joint filler. If the surface material is not adequately bedded into the base then the joint filler will not withstand the twisting (torque) caused when a vehicle changes direction. Most vehicular drives will have a strong and consequently less permeable mix of the base material. EASYJoint CAN still be used but a 'dry' method of installation should be used. Refer to instructions for domestic driveways. Using EASYJoint is particularly ideal for jointing cobble driveways, it's a fast and EASY way to achieve incredible results, joints that will last!
In freezing conditions can I still use EASYJoint?
Yes however in freezing conditions or in falling temperatures below 3 degrees Celsius, please refer to the instructions and the dry method of installation.
Can you keep left over EASYJoint from going hard?
Yes, we make it EASY. Pour any unused EASYJoint back into the tub and cover it with at least 50mm (2 inches) of water. It should remain stable and safe to use for up to several months providing it remains covered with water (subject to environmental influences). EASYJoint will always go rock hard as soon as it is in contact with the air, it does not need water to cure.
Will EASYJoint set hard in every case?
Providing it is allowed to dry out, YES! EASYJoint requires air to cure but water will stop this process happening. As long as it is allowed to dry out it will go hard. EASYJoint will not go hard if left in damp or wet joints that never fully dry out.
Is there a visual change in the EASYJoint colour over time?
EASYJoint is an entirely natural product, because dirty water can drain through the joint, over time the appearance may change, this will not affect the integrity of the product. The joints can be cleaned by the cautious use of a pressure washer, keeping a fan type nozzle, at an angle, no closer than 150mm from the surface.
Is EASYJoint guaranteed?
Not in the sense that it will last forever, nor can we guarantee its lifespan. However we can say that its predecessors, earlier derivatives of the current product, have been in use for more than 20 years and where the ground conditions are stable and a good sub-base has been employed, they have stood the test of time - much longer in most instances than a cement alternative. The basic technology is sound and proven and in our experience it will outlive most alternatives.
Can I top up joints when the EASYJoint has set hard?
No. Our instructions state that any sagging of a joint must be topped up whilst it is still wet (or has not cured). The problem is that if you try to top up a joint it will not bond properly with the existing joint and over time the joint will fail because it will be a weak paving joint. We recommend the depth of the joints are kept to a minimum of 25mm.
Can EASYJoint be sealed?
Yes, although if you are going to use a sealer it makes sense to do it before you joint with EASYJoint. If you have decided to joint the paving with EASYJoint before sealing, you will need to wait four weeks for the EASYJoint to go fully hard. We recommend sealing paving before jointing the paving. Look at our EASYSealer range to see what sealer best suits your needs.
Note: EASYJoint continues to harden for several weeks and achieves its full strength after approximately 1 month.
Can EASYJoint be used with Porcelain tiles?
Yes you can use our jointing compound with porcelain tiles, in fact some specialist suppliers only recommend EASYJoint for jointing them! You must follow the instructions carefully when using porcelain tiles and depending on whether they are for indoor or outdoor use, be careful what bedding mix they are laid on. Porcelain is impermeable (it will not allow water to pass through it) and it is possible to use the dry application method to joint it (follow detailed instructions). If using the wet method ensure that the bedding mix is permeable and made up from a mix no stronger of 6 parts sharp sand to one cement.
Brief usage instructions
Download the EASYJoint Instructions
The following brief instructions should not be relied upon alone. They are designed to give an overview of a typical Wet Application Method which is suitable for the majority of paving jobs. More detailed instructions & advice on how to use EASYJoint are printed separately within the tub & are available on this site.
The application is made easier if two operators work together. Most paving can be protected by thoroughly soaking it with water for a minimum of 10 minutes before application. The wetter the surface the greater the protection.
Tip one paving compound bag onto the soaked paving. Keep the hose running throughout the application process. Do not pile or leave EASYJoint standing in one spot, nor allow the paving to dry out with the compound on its surface
Simultaneously sweep & flush the EASYJoint into the joints. Keep the hose low to the paving & continuously wash both the paving & the compound ahead of & behind the broom. Never allow the paving to dry.
Once the first bag is used open another & repeat the process. Keep the hose running to keep paving wet. Keep the compound moving at all times.
Top up sagging joints with more EASYJoint. Repeat the washing process, flushing the compound into the joints. Fill to just below the paving surface.
Once all the joints are uniformly filled, reduce the water pressure & apply a final gentle spray of water to wash away any final traces of compound & the binding oil.
In warm dry conditions, once drained, the joint will be firm within 18 hrs & sets hard in 24 hrs. Wet or cold weather considerably extends the curing time.
Coverage will greatly vary according to the size of the joint. Because accuracy of gap width & depth cannot be uniformly guaranteed, the table can only be considered a guide and assumes the stated gap dimensions. For a more accurate estimate of coverage contact us.
For joint sizes and further information, view our full instructions.
Note: EASYJoint continues to harden for several weeks and achieves its full strength after approximately 1 month.